Введение
DROPS 177-30
seahugshawl
DROPS design: Pattern no la-032
Yarn group A
Measurements: Approx. 37 x 200 cm
Materials:
DROPS LACE from Garnstudio (belongs to yarn group A)
100 g colour 6410, turquoise
DROPS CIRCULAR NEEDLE SIZE 3 mm - NOTE: Read about the knitting tension below.
+ an extra circular needle in the same size for cast-on edge.
You might also like...
Women Accessories Scarves Shawlslace
Pattern instructions
Keep the screen on while knitting
Tools
KNITTING TENSION
KNITTING TENSION
The scarf will be soaked and stretched to size afterwards. The knitting tension is therefore not that important, but to get a sense of whether you are knitting to loose/hard work a test in stocking stitch on needle size 3 mm. The test should give approx. 24 stitches and 32 rows = 10 cm in width and 10 cm vertically.
GARTER STITCH (back and forth):
1 ridge = knit 2 rows.
PATTERN
See diagrams A.1 to A.4. Diagrams show all rows in pattern seen from the right side.
SHAPING
When using another yarn from yarn group A, there is no need to stretch to measurements, but place it gently out in shape and leave to dry. Repeat the process when the scarf has been washed.
SCARF
Worked in 2 parts that are sewn together in the middle.
PART 1: Cast on 116 stitches on 2 circular needles size 3 mm with Lace. Pull out one circular needle (cast-on is done like this to avoid a tight cast-on edge). Work 2 ridges in GARTER STITCH - see explanation above. Work next row as follows from the right side: 3 edge stitches in garter stitch, work A.1 over the next 110 stitches (= 5 repetitions of 22 stitches), finish with 3 edge stitches in garter stitch. Continue pattern like this. When A.1 has been worked 1 time vertically, there are 86 stitches on row.
* Work next row as follows from right side: 3 edge stitches in garter stitch, work A.2 over the next 80 stitches (= 5 repetitions of 16 stitches), finish with 3 edge stitches in garter stitch. Continue pattern like this. When A.2 has been worked 1 time vertically, work A.3 the same way. When A.3 has been worked 2 times vertically, work A.4 the same way . After A.4 repeat from -* 3 more times (= 4 repetitions in total) but finish last repetition after row marked with arrow in diagram. Work 2 ridges in garter stitch, slip stitches on 1 stitch holder or LOOSELY cast off by knitting from right side.
PART 2: Work as part 1.
ASSEMBLY
Sew the two part tog in the middle with grafting/kitchener stitches (if stitches have been cast off sew together inside cast-off edge).
BLOCKING
Place the scarf in lukewarm water until it is soaking wet. Carefully squeeze out the water - do not twist. Roll the scarf in a towel and squeeze to remove more water - the scarf will now only be moist. Place the scarf on a carpet or mattress - carefully stretch it out to size and fasten it with pins. Leave to dry. Repeat the process when the piece has been washed. NOTE: If another yarn in yarn group A has been used - READ SHAPING!
Diagram
= knit from the right side, purl from the wrong side
= no stitch, skip this square
= between 2 stitches make 2 yarn-over on needle, on next row purl one yarn-over and drop the other yarn-over off the needle (= hole)
= between 2 stitches make 3 yarn-over on needle, on next row purl one yarn over, purl the second yarn-over twisted and drop the third yarn-over off the needle (= hole)
= BOBBLE: Knit 1, 1 yarn-over, knit 1, 1 yarn-over, knit 1 in same stitch (= 5 stitches), turn piece. Work 4 rows in stocking stitch over these 5 stitches Then pass second stitch on right needle over first stitch, pass third stitch over first stitch, pass fourth stitch over first stitch and pass fifth stitch over first stitch (= 1 stitch remains).
= knit 2 together
= slip 1 stitch knitwise, knit 1, pass slipped stitch over stitch worked
