Введение
DROPS 166-13
ruthset
DROPS design: Pattern no li-067
Yarn group B
HAT
Size: One-size
Head circumference: approx. 56/60 cm
Materials:
DROPS LIMA from Garnstudio
100 g colour no 8112, ice blue
DROPS DOUBLE POINTED NEEDLES and CIRCULAR NEEDLE (40 cm) SIZE 4 mm - or size needed to get 21 sts x 28 rows in stocking st = 10 x 10 cm.
NECK WARMER
Size: S - M - L
Measurements: Circumference: approx. 57-63-67 cm Height 22-24-26 cm
Materials:
DROPS LIMA from Garnstudio
150 g for all sizes colour no 8112, ice blue
DROPS CIRCULAR NEEDLE (40 cm) SIZE 4 mm - or size needed to get 21 sts x 28 rows in stocking st = 10 x 10 cm.
MITTENS
Size: One-size
Materials:
DROPS LIMA from Garnstudio
100 g colour no 8112, ice blue
DROPS DOUBLE POINTED NEEDLES SIZE 3.5 mm - or size needed to get 22 sts x 30 rows in stocking st = 10 x 10 cm.
You might also like...
Women Accessories Hats Neck Warmers Gloves & Mittens Beanies Mittensbottom up rib
Pattern instructions
Keep the screen on while knitting
Tools
PATTERN
See diagrams A.1-A.2.
DECREASE TIP (applies to mittens):
Dec before marker as follows: Work until 2 sts remain before marker, K 2 tog.
Dec after marker as follows: Work until marker, slip 1 st as if to K, K 1, psso.
HAT
Worked in the round on circular needle/double pointed needles. Cast on 108 sts on circular needle size 4 mm with Lima. K 1 round. Then work rib = P 2/K 1 over all sts until piece measures 4 cm. Then work diagram A.1. REMEMBER THE KNITTING TENSION When piece measures 16 cm, insert 9 marker in the hat, 12 sts between each marker, insert first marker after 12 sts (i.e. after 1 st K). On next round, dec 1 st before every marker by K the last 2 sts tog. Continue with K over K, garter st over garter st and P over P. Repeat dec every other round 10 times in total = 18 sts. On next round K tog all sts 2 by 2 = 9 sts. Cut the yarn and pull it through the remaining sts, tighten tog and fasten.
The hat measures approx. 25 cm vertically.
NECK WARMER
Worked in the round on circular needle. Cast on 120-132-141 sts on circular needle size 4 mm with Lima. K 1 round. Work rib = P 2/K 1. When piece measures 4 cm, work A.1 over all sts. REMEMBER THE KNITTING TENSION When piece measures 18-20-22 cm, work rib over all sts (= P 2/K 1). When piece measures 22-24-26 cm, K 1 round. Cast off.
RIGHT MITTEN
Worked in the round on double pointed needles. Cast on 42 sts on double pointed needles size 3.5 mm with Lima. K 1 round. Then work rib = K 1/P 2 over all sts until piece measures 4 cm. Then work A.2 over all sts. Insert 1 marker in the first st on round (= K st). REMEMBER THE KNITTING TENSION! when piece measures 10 cm, inc for thumb by make a YO on each side of st with marker, K YO twisted on next round. Repeat inc every other round 5 more times - inc on each side of all thumb sts every time, i.e. at next inc, inc on every side of 3 sts, then 5 sts etc. – work inc sts in stocking st. After all inc, there are 13 thumb sts and 54 sts in total. After last inc slip thumb sts on a stitch holder and cast on 1 new st over sts on stitch holder = 42 sts. Continue pattern, K the new sts as before. When piece measures 23 cm, insert 4 markers in the piece as follows: Work 1 st as before, insert 1st marker, work 2 sts as before, insert 2nd marker, work 19 sts as before (last st is K 1), insert 3rd marker, work 2 sts as before, insert 4th marker, work the rest of round as before. On next round, dec before 1st and 3rd marker and after 2nd and 4th marker – Read DECREASE TIP (= 4 sts dec). Repeat dec every round, 7 more times = 10 sts. Cut the yarn and pull it through the remaining sts, tighten tog and fasten. Piece measures approx. 26 cm.
THUMB
Slip the 13 sts over thumb gusset on double pointed needles size 3.5 mm and pick in addition up 3 sts along the edge behind thumb sts = 16 sts. Work in stocking st until the thumb itself measures approx. 5 cm (try on the mitten, approx. ½ cm remains until finished measurements).
K all sts tog 2 by 2 = 8 sts. K 1 round. K all sts tog 2 by 2 = 4 sts. Cut the yarn and pull it through the remaining sts, tighten tog and fasten.
LEFT MITTEN
Cast on and work as right mitten. Inc for thumb on each side of the 22nd st on round (= K st). Insert markers as follows: Insert 1st marker at beg of round, work 19 sts as before, insert 2nd marker, work 2 sts as before, insert 3rd marker, work 19 sts as before, insert 4th marker, work the rest of round as before. Dec after 1st and 3rd marker and before 2nd and 4th marker.
Diagram
= K
= P
