Введение
DROPS 103-31
The set consist of: Felted DROPS hat and a DROPS scarf knitted in moss sts with”Snow”.
Pattern
Videos
Lessons
FAQ
Comments (15)
Change language:
English (UK/cm)
DROPS 103-31
Suggest a name
HAT
To fit head circumference: approx 55-57-60 cm
Circumference before felting: approx 75-78-82 cm
Circumference after felting: approx. 57-60-63 cm measured at the outside of the hat.
Materials: DROPS Snow
200 g, for all sizes clr. no. 46, middle grey.
DROPS pointed needles size 9 mm – or the size needed to obtain the correct knitting tension.
You might also like...
Women Let's Get Felting! Accessories Hats Scarves Beanies Felted Hatsbottom up chunky knits moss st
Pattern instructions
Keep the screen on while knitting
Tools
Knitting tension: 10 sts x 14 rows in stocking sts = 10 x 10 cm before felting.
After felting: 13 sts x 25 rows = 10 x 10 cm
Hat: Cast on 77-80-84 sts on needle size 9 mm with Snow. Knit 4 rows of garter sts. Continue in stocking sts. When the piece measures 24-25-26 cm knit 4 rows of garter sts over all sts before casting off.
Top: Pick up 77-80-84 sts from the WS at the top of the hat 1 row below the casting off edge. This gives the hat a small edge. K 1 row from the RS at the same time inc/dec sts evenly distributed to = 78-78-78 sts.
Insert 6 MT (marking threads) in the work as follows: 1st MT after 13 sts , 2nd MT after 26 sts, 3rd. MT after 39 sts, 4th MT after 52 sts, 5th MT after 65 sts and 6th MT at the end of row. Knit in stocking sts at the same time dec. 1 sts from the RS before each MT on every other row as follows: K2 tog. a total of 12 times = 6 sts left. The top measures approx. 17 cm in diameter and the complete hat measures approx. 42-43-44 cm from the casting on edge. Pull a thread through the remaining sts and pull tight.
Assembly: Sew the hat tog. in the outer part of the edge mid back all the way to the top.
FELTING
The piece can be felted either in the washing machine or the tumble dryer – read description below.
Remember: Subsequent washes are as for a normal wool garment.
IN WASHING MACHINE
Washing machines will vary when felting. If the piece is not felted enough, it can be felted again. If it is felted too much, it can be stretched to the correct size while still wet.
DO THE FOLLOWING
Lay the piece in the washing machine, using a programme of approx. 40 minutes (not a wool programme).
Wash at 40 degrees without pre-wash, detergent is optional. After washing, shape the piece while it is still wet.
IN TUMBLE DRYER
Felting in a tumble dryer gives good control over the degree of felting. The tumble dryer can be opened during drying to check the size of the piece. If it is not felted enough it can be thoroughly wetted and felted again. If it is felted too much it can be stretched to the correct size while still wet.
DO THE FOLLOWING
Lay the piece in water so it becomes completely wet, then place it in the tumble dryer and begin the drying process. Dry to the desired size, checking regularly.
Scarf
Measures: 15 cm x 165 cm
Materials: DROPS Snow
250 g, clr. no. 46, middle grey.
DROPS pointed needles size 10 mm – or the size needed to obtain the correct knitting tension.
Knitting tension: 9 sts x 12 rows in moss sts = 10 x 10 cm
Moss sts: 1st row: K1, P1 , repeat from -. 2nd row: K over P and P over K. Repeat the 2 rows.
Scarf: Remember the knitting tension! Cast on 14 sts on needle size 10 mm with Snow. Knit in moss sts – see explanation above – until the piece measures 165 cm or the length you wish. Cast off in moss sts.
